| Step | | Procedure & Parts & Tools |
| 1 |
|
LOCATE THE DRAIN HOSES ON THE BACK OF THE MACHINE
|
| 2 |
|
PULL TO REMOVE THE RED CAPPED HOSE FROM MACHINE. PLACE HOSE NEAR DRAIN AND REMOVE CAP
|
| 3 |
|
PULL TO REMOVE THE BLUE CAPPED HOSE FROM MACHINE. PLACE HOSE NEAR DRAIN AND REMOVE CAP
|
| 4 |
|
PULL TO REMOVE THE BLUE CAPPED HOSE FROM THE MANUAL SOLUTION VALVE ASSEMBLY
| Wrench-Allen metric 6.0mm |
|
|
| 5 |
|
LOCATE MANUAL SOLUTION VALVE LINKAGE
|
| 6 |
|
REMOVE THE BOTTOM BOLT FROM THE MANUAL SOLUTION VALVE
| Torx T30 |
|
|
| 7 |
|
PULL THE BOLT FROM THE MACHINE
|
| 8 |
|
TURN THE MANUAL SOLUTION VALVE A 1/4 OF A TURN TO THE LEFT
|
| 9 |
|
UNHOOK THE LINKAGE FROM THE MANUAL SOLUTION VALVE TO DISCONNECT IT FROM THE MACHINE
|
| 10 |
|
UNHOOK THE LINKAGE FROM THE MANUAL SOLUTION VALVE LEVER TO DISCONNECT IT FROM THE MACHINE
|
| 11 |
|
REMOVE THE TOP BOLT FROM THE MANUAL SOLUTION VALVE
| Torx T30 |
|
|
| 12 |
|
PULL THE BOLT FROM THE MACHINE
|
| 13 |
|
PULL THE MANUAL SOLUTION VALVE TO REMOVE IT FROM THE MACHINE
|
| 14 |
|
RELEASE THE HOSE CLAMP FROM THE HOSE
| Screwdriver-flat tip |
|
|
| 15 |
|
PULL TO REMOVE THE HOSE FROM THE MACHINE
|
| 16 |
|
REMOVE VAC HOSE COVER SCREW
| Torx T30 |
|
|
| 17 |
|
REMOVE 2 VAC HOSE COVER SCREWS
| Torx T30 |
|
|
| 18 |
|
PULL TO REMOVE VAC HOSE COVER FROM MACHINE
|
| 19 |
|
UNCLAMP THE HOSE CLAMP AND PULL TO REMOVE THE VAC HOSE FROM THE MACHINE.
| Screwdriver-flat tip |
|
|
| 20 |
|
REMOVE 2 SCREWS HOLDING CHARGER PLUG
| Screwdriver-phillips |
|
|
| 21 |
|
REMOVE 2 SCREWS HOLDING SQUEEGEE CABLE BRACKET
| Torx T30 |
|
|
| 22 |
|
REMOVE 2 SCREWS HOLDING DRAIN HOSE BRACKETS
| Torx T30 |
|
|
| 23 |
|
RAISE THE TANK COVER, PROP OPEN AND PULL TO REMOVE THE FILTER BASKET
|
| 24 |
|
REMOVE 2 SCREWS HOLDING DOSING CUP AND REMOVE DOSING CUP FROM MACHINE. CLOSE THE COVER.
| Torx T30 |
|
|
| 25 |
|
REMOVE SCREW HOLDING TANK COVER AXLE
| Torx T30 |
|
|
| 26 |
|
REMOVE THE 2 TANK BOLTS ON EACH SIDE OF THE MACHINE. THESE BOLTS ARE LOCATED AT THE FRONT OF THE MACHINE AT THE BASE.
|
| 27 |
|
RAISE THE TANK UP TO OPEN IT.
| Wrench-Allen metric 6.0mm |
|
|
| 28 |
|
PUSH THE CHARGER PLUG THRU THE OPENING IN THE TANK
|
| 29 |
|
REMOVE 4 SCREWS HOLDING THE TANK LOCKS TO THE TANK
| Torx T30 |
|
|
| 30 |
|
REMOVE 2 SCREWS HOLDING THE BOTTOM AXLE TO BASE. PULL TO REMOVE AXLE.
| Torx T30 |
|
|
| 31 |
|
PULL TO REMOVE TANK FROM MACHINE BASE.
|
| 32 |
|
REVERSE STEPS 4 THRU 31 TO INSTALL A NEW TANK
|